Result and Success Fields

When you perform a command, the last screen in your workflow presents you with a results list. This table provides details of what the results mean. All result fields are listed here for all ERT and meter types and any command you might perform. They are listed in alphabetical order.

Field	Description
Active Events	A list of ongoing events the device has recorded and the time and date at which it they started. Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table. Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
Active Period During Wakeup	The length of time in which the ERT or meter stays awake and is available for downlink traffic communication after waking from PSM.
APN Name	The Access Point Name (APN) for the gateway used between the cellular service provider and the network. Important: For some meter and ERT types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
Application Configuration	The current .zip application configuration file attached to the device.
Audit Mode Duration	The number of minutes the device remains in Audit Mode. While in Audit Mode, the device will bubble-up every four seconds.
Auto Wake Up Enabled	Whether the Automatic Factory Mode Wakeup on Pulses Detected setting is enabled or not. True False
Automatic Disconnect (Intelis Gas Meters, Openway Riva Intelis Gas Meters, and Gen5 Intelis Gas Meters only)	If the meter's Automatic High Flow Shutoff programming is enabled, indicates if a high flow alarm was initiated. Volume flow checks that detect more than 0.18 CF (5L) initiate an automatic disconnect. High Flow Not Detected. A high flow alarm is not initiated. Important: For some ERT and meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
Auto High Flow Shutoff Or Automatic High Flow Shutoff	Whether the meter is programmed to shut off automatically in response to a high flow event. Enabled. The Automatic High Flow Shutoff feature is enabled. Disabled. The Automatic High Flow Shutoff feature is disabled.
Auto High Temperature Shutoff Or Automatic High Temperature Shutoff	Whether the meter is programmed to shut off automatically in response to a high temperature event. Enabled. The Automatic High Temperature Shutoff feature is enabled. Disabled. The Automatic High Temperature Shutoff feature is disabled.
Backflow Register (Intelis Water Meters only)	The current reading of the meter's backflow consumption register. No backflow register. The meter does not support recording backflow consumption.
Band Bitmap	A bitmap that restricts the modem to searching specific frequency bands for a cellular carrier network.
Battery Status	The state of the meter or ERT battery's electrical charge. Good. The battery's charge is at greater than ten percent of capacity. Bad. The battery's charge is at ten percent or less of capacity.
Battery Utilization Threshold	Micro-coulomb threshold used to protect the cellular modem in the device from consuming too much energy when attempting transmiossion. When the threshold is exceeded, the device stops transmitting and puts the cellular modem into airplane mode to conserve battery.
Bubble Up or Bubble Up Rate	How often the ERT automatically transmits, or bubbles up, its SCM. The meaning of the value in this field varies by ERT type. See the ERT's documentation for details. Occasionally, for some ERTs that don't support bubble-up mode, a value of Disabled displays.
Carrier Operator ID	The name of the cellular service provider and its associated number. The number is based on the country where you are receiving service.
Carrier PDP Type	The packet data protocol (PDP) networking type the cellular service provider uses to transmit data using Internet Protocol.
CE Address Index	The current CE address offset index.
Cellular Data Context	A particular data context supported by the cellular modern for a particular carrier.
Configuration Tag	The current OWOC configuration attached to the device.
Count Rate	The metrology value used with PCOMP, rollover, and counts to calculate the consumption value. Count Rate is displayed only if Field Tools is unable to determine the meter configuration. If you were not required to enter the meter's number of dials and billing units during the Check Endpoint command, then Count Rate is not returned in the Check Endpoint response.
Count Sample Rate
Current Backoff	The connection retry backoff value, in seconds, when the Network Status is one other than Joined or Idle.
Current Meter Pressure	The current pressure gauge reading from the Intelis Gas Meter. A value is returned only for Intelis Gas Meters that support the internal pressure gauge feature. A returned value of Not Supported means the meter does not support the internal pressure gauge feature.
Current Gas Temperature	The current temperature reading and unit of measure for both Celsius and Fahrenheit. or A description of how the current gas temperature relates to the temperature threshold: Temperature Below Threshold. Important: For some ERT and meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
Cut Detected	Whether or not the ERT has detected a cut cable. (For the 100G, this applies to remote-mount modules only.) Yes. The ERT has detected a cut cable sometime during the last 40 days. No. The ERT has not detected a cut cable within the last 40 days.
Device IP Address	No Cell Connection. Indicates the Itron cellular module is currently not connected to a cellular service provider's network.
Device Type/Subtype	The meter or ERT's device type and subtype: for example, OW Riva 500G ERT Module/Remote.
DLCA Certificate Serial Number	The serial number for the driver's license certificate authority (DLCA) that issued the driver's license (DL) to the ERT module to allow it to become a member of the network.
DL Certificate Serial Number	The serial number for the driver's license (DL) issued to the ERT module to allow it to become a member of the network.
Display Units	The meter's selected unit of measure for volume: Imperial. Volume measured in centum cubic feet (CCF) and flow rate expressed in cubic feet per hour (CFH). Metric. Volume measured in cubic meters per hour (M³) and flow rate expressed in cubic meters per hour (CMH).
Encoder Driver	The product name or version number of the ERT's encoder driver, which is used to decode register data.
Encoder Firmware	The meter encoder's firmware version number.
Encoder Fixed Firmware	The meter encoder's fixed firmware version number.
Endpoint Functions Correctly	Indicates if the ERT is registered correctly. True False
Encoder Latency (Encoded registers only)	How often the ERT attempts to communicate with the encoder register to collect a reading. The default setting is 1 hour: 5 minutes 15 minutes 1 hour 6 hours Important: Setting encoder latency to more frequent than 1 hour significantly reduces the ERT's battery life.
Encoder NLR Firmware	The meter encoder's non-legally relevant (NLR) firmware version.
Endpoint ID	The identification number of the ERT or meter that was read, checked, or programmed.
Endpoint Reading	The meter reading, as indicated by the ERT. Note: For 100G ERTs, a No Read result is returned if a cut cable tamper is discovered. Important: For some ERT and meter types, this field's value is a link to reformat the endpoint reading. The formatting fields are listed alphabetically within this table.
Endpoint Subtype	The endpoint subtype; for example, 100G DL. Note: 100W+-P indicates that the ERT is a 100W+ with an attached peripheral device, such as a leak sensor.
Endpoint Type	The ERT model: for example, 100G.
EPS Network Registration Status	Not Registered: Device not searching
Event Description	A brief description of the event. For more information, see Tampers and Events.
Event Name	The name of the event. For more information, see Tampers and Events.
Event Time	The date and time at which the event occurred.
Events	A list of events the device has recorded and the time and date at which it they occurred. Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
External Antenna	Connected. The module has an external antenna. Not connected. The module does not have an external antenna.
FDM User
Firmware Information or Firmware Info	The number of firmware download (FWDL) operations that have been initiated in the meter or ERT. or The meter register's firmware version number. Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
Firmware Version (Itron cellular ERTs only)	The current firmware version for the Itron cellular device's modem.
Geo Mode Status	Indicates the module's current status in the geomode linking process. Possible values depend on if the module is functioning as a geoendpoint or a georelay. Off. The module is neither linked nor in the process of linking to another module. The following statuses are applicable if the module is a geoendpoint. They indicate the steps through which it passes while attempting to establish a geomode link with a georelay: GeoEndpoint Beaconing GeoEndpoint Connected The remaining statuses are applicable if the module is a georelay. They indicate the steps through which it passes while attempting to establish a geomode link with a geoendpoint: Relay Acquiring Relay Waiting Relay Sending Request Relay Connected
Granted PSM Configuration	These parameters record the values for PSM TAU Cycle and Active Period During Wakeup that have been granted by the cellular tower.
Headend IP Address	The IP address for the cellular service provider's headend.
High Flow	The status of the meter's gas flow as it relates to high flow thresholds: High Flow Not Detected. Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
High Flow Aggregation Window	The rolling window over which a high flow event is determined.
High Flow Sampling Frequency	How often flow is sampled for a high flow event.
High Flow Threshold	The threshold at which the high flow event is considered high.
High Temperature	The status of the meter's temperature reading as it relates to high temperature thresholds: High Temperature Not Detected. Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
High Temperature Threshold	The threshold at which the temperature is considered high.
Hop Config	Indicates the hop configuration the ERT uses to randomize the communication channels over which it transmits its bubble-up messages: Hop on 120 channels. The ERT transmits its bubble-up messages across 120 channels, randomly selected in the range of 903 MHz to 926.8 MHz. Hop on 120 channels offset 50 kHz. The ERT transmits its bubble-up messages across 120 channels, randomly selected in the range of 903.05 MHz to 926 MHz. Hop on 50 channels. The ERT transmits its bubble-up messages across the most reliable 50 channels within the range of 903 MHz to 926.8 MHz, as determined by the Itron Fixed Network system. NA. Not applicable. The ERT or meter's communication channel is not randomized with a hop configuration.
ICCID	The integrated circuit card ID (ICCID) is the unique serial number for the Itron cellular device's internal SIM card.
IMEI	The international mobile equipment identity (IMEI) is a unique 15-digit number associated with the Itron cellular device.
IMSI	The international mobile subscriber identity (IMSI) is a unique number identifying the Global System for Mobile Communications (GSM) operator.
Initial Network Scan	Parameter for configuring the backoff policy for network scanning during the initial network scan.
Initial Reading Programmed	The meter reading on the register, at the time the meter was last programmed.
Last Auto Disconnect Trigger	If the meter has experienced an auto disconnect, the condition that caused it. For more information, see Valve Operations in the Intelis Gas Family of Meters.
Last Operation Detail	Any further details Field Tools provides about the Last Operation Result.
Last Operation Time	The date and time at which the last operation occurred.
Last Command Sent or Last Operational Result	The most recent command performed on the meter.
Last Command Status or Last Successful Condition	The current status of the valve as a result of the last performed command: Service Disconnected. The valve is closed and gas flow is stopped. Valve Armed. The valve is primed to open when the meter's hardware button is pressed. Arm Failed. The last command sent was Arm for Connection, but Field Tools was unable to successfully perform the command. Service Connected. The valve is open and gas is flowing. Restricted. The valve is open and water is flowing at 10-90% of it regular flow. Connected. The valve is open and water is flowing. Disconnected. The valve is closed and water flow is stopped. Automatic Disconnect. The meter's high-flow or high temperature sensor detected a high flow or high temperature event and the meter automatically performed a shutoff command. The valve is closed and service is disconnected, gas flow is stopped. For more information, see Valve Operations in the Intelis Gas Family of Meters.
Last Good Read	The last meter reading as indicated by the ERT before it started reporting No Read or Invalid (stuck digit). This response field displays only for 100 series water ERTs whose Endpoint Reading field is reported as No Read or Invalid (stuck digit).
Leak Detected (100W)	Yes. The ERT has detected a leak. No. The ERT has not detected a leak.
Leak Period	The time interval, in hours, the ERT uses to determine whether there has been a leak, as defined by the Leak Threshold value. For example, assume the Leak Period value is 168 and the Leak Threshold value is 0. In this case, the ERT must detect at least one count-switch closure per hour, every hour, for seven consecutive days before indicating a leak. The default Leak Period value is 168.
Leak Sensor Or Leak Sensor Info	Whether or not the ERT has a leak sensor: Connected Not Connected Important: For some ERT types, this field's value is a link to open the following additional info: Firmware Version. The firmware version on the leak sensor Hardware Version. The leak sensor's hardware version. Serial Number. Theleak sensor's serial number.
Leak Threshold	The number of meter count-switch closures per hour, per leak period that indicates a leak. If the number of count-switch closures per hour during the period specified in the Leak Period field is less than or equal to the Leak Threshold value, the ERT considers the flow of water to be zero (no leak). If the number of count-switch closures per hour during this period is above the Leak Period value, the ERT considers it to be a non-zero flow. The default Leak Threshold value is 0.
Lock Level	The ERT's lock level: No lock. Allows an Itron mobile device with the correct utility ID to reprogram the ERT module. Soft lock. Must first be unlocked by a mobile device that has been configured with your utility's ID before it can be programmed. Hard lock. Prevents billing parameters such as consumption, number of dials, drive rate, or PCOMP from reprogramming. System parameters such as operation mode (M/HH, H2R, and so on) are available for reprogramming.
Low Debounce Sample Rate
MAC Current Backoff	When the Network Status is in the Joining state, this is the current backoff value, in seconds, for the MAC parent selection process.
MAC Current Retries	When the Network Status is in the Joining state, this is the current number of retries the MAC has made in the MAC parent selection process.
MAC Status	The status of the parent selection process when the Network Status is in the Joining state. When the Network Status is not in the Joining state, this status is not useful. The status can be one of the following: Disabled Idle Reset Scanning Additional Scan Start
Magnetic Tamper(100G)	The ERT or meter's magnetic tamper value, which increments whenever the module is exposed to a strong external magnetic field. Exposure to a magnetic field can result in under-reported consumption or even cause the ERT module to stop counting. This value does not automatically reset when the module is programmed. Valid values are 0-3. Note: On 100G remote-mount ERT modules, the cut cable tamper replaces the magnetic tamper.
Manufacturer	The modem manufacturer of the cellular modem in the Itron cellular ERT. Or The manufacturer of the water meter on which the water ERT is installed.
Maximum Backoff	The maximum interval, in seconds, between network scans.
MDN Number	The mobile directory number (MDN) assigned to the Itron cellular device upon activation. A value of No Cell Connection indicates that the device is not yet activated by a cellular service provider.
Measurement Unit Firmware CRC	The CRC of the measurement unit firmware.
Meter Configuration	The meter's make and number of dials and unit of measure, as indicated by the ERT.
Meter Reading	The meter reading, as indicated by the ERT. Note: For 100G ERTs, a No Read result is returned if a cut cable tamper is discovered.
Meter State	Commissioned
Minimum Backoff	The minimum interval, in seconds, between network scans.
Mode Change Counter	The number of times the ERT or meter received a non-metrology programming command.
Mode Name	The power level at which the ERT transmits. Examples: Mobile/HH. Mobile HP. Transmits every 1 minute at +24dBm. Hard-to-Read.
Model	The model number of the cellular modem in the Itron cellular ERT.
Multicast Address Written	Indicates if the ERT is registered successfully. True False
Network ID	(GenX devices only) A 1- to 5-digit number representing the ID of the network the device will attempt to join. All active devices in a utility company's service area must use the same network ID.
Network Parameters	For some meter types, the meter or ERT's SSID is displayed as a link. Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
Network Status	The status of the device's current network joining attempt. The status can be one of the following: Idle Started Initializing DLL Joining Attempting to join Establishing Security Joined Not Registered: Device not searching Important: For some meter and ERT types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
NMS Address Index	The current NMS address offset index.
Non-Temperature Corrected Index	The consumption value, without a temperature compensation applied.
Number of FWDL Initiated	The number of firmware download (FWDL) operations that have been initiated in the meter.
Operating Mode	Indicates what, if any, network connection mode the cellular service provider is using to limit the device's power and network bandwidth consumption. PSM. Power-saving mode
Operational State	The method used to perform the last command: Normal Override Auto disconnect
Operations Manager Connected	Indicates if the ERT is registered successfully. True False
Operator Certificate Serial Number	The serial number for the operator certificate (network).
Operator Certificate Subject DN	The Subject DN of the Operator certificate. Subject DN is used to identify the network operator. Updated operator certificates must have same subject DN to be accepted.
Operator Name	The cellular service provider for the Itron cellular device. A value of No Cell Connection indicates that the device isn't connected to a cellular network.
Out of Coverage Network	Parameter for configuring the backoff policy for network scanning during poor signal coverage conditions.
OWOC File	The current OWOC configuration attached to the device.
Packet Type	The standard consumption message packet type the ERT or meter is configured to transmit: SCM+ NIM with SCM+ Contingency
PCOMP	The (gas) meter's pressure compensation factor.
Peripheral Device	The peripheral device that is connected to the ERT. For example: Remote Disconnect
Pressure Compensation	The (gas) meter's pressure compensation factor.
Previous Cut Detected	In the past, a cut cable was detected on the ERT.
Primary DNS Server	No Cell Connection
Primary Index Correction	Indicates if the primary index is temperature compensated or non-temperature compensated. Temperature Corrected Index
Program Change Counter	The number of times the ERT or meter received a programming command that affected its metrology.
Programmed Meter Configuration or Programmed Configuration	The meter's number of dials and unit of measure, as indicated by the ERT. Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
Programmed Mode	The power level at which the ERT transmits. Examples: Mobile/HH Mobile HP Hard-to-Read (H2R) Important: For some ERT and meter types, this field's value is a link to open additional info. The additional info values are listed in this table.
Projected Remaining Years	The meter's estimated remaining years of battery life, calculated based on the current Battery Counter value, which takes into account battery usage due to past ERT operations. Because the amount of future operations is dependent on how the utility interacts with the ERT, the Projected Remaining Years is not a guarantee of remaining battery life.
PSM TAU Cycle	The tracking area update (TAU) period defines the time over which the device will stay in power saving mode (PSM). When the TAU timer expires the devices wakes up to refresh its connection to the cellular tower and to make itself available for downllink traffic communication.
Pulse Factor	The number by which the ERT multiplies the number of meter pulses to convert it into a usage value.
Radio Access Technology
Reading	The meter reading, as indicated by the ERT. Note: For 100G ERTs, a No Read result is returned if a cut cable tamper is discovered.
Recent Parent MAC Address	The MAC address for parent CPDs (network node, up to four) that the ERT module recently established a connection within. o Note: Intention is to show ‘recently’ being last few months but due to implementation details, think it does not show ‘past’ CPD.
Register Config	The number of meter dials.
Register Firmware	The meter register's firmware version number.
Register Fixed Firmware	The meter register's fixed firmware's version number.
Register Type	May be either of the following values: Encoder Pulser Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
Registration Status Bits	Indicates whether the meter is registered successfully. Responds with a True or False value for each of the following: Endpoint Functions Correctly Operations Manager Connection Multicast Addresses Written Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
Requested PSM Configuration	Parameters are the values requested of the ERT or meter during configuration.
Retries Attempted	The number of times the device has tried to complete the current stage of network joining. When Network Status is Joined or Idle, this value is not useful.
Reverse Flow	Yes. The ERT has detected a reverse flow. No. The ERT has not detected a reverse flow.
RF Power	The power level, in dBm units, at which the meter or ERT transmits data. This value corresponds to the communication mode the ERT is configured for, as follows: +10 dBm. Mobile/handheld (M/HH mode). +24 dBm. High-power (HP), hard-to-read (H2R), and Fixed Network (FN) mode. +27 dBm. High power (HP), and Fixed Network (FN) mode. +27 dBm. ERT-GTWY mode.
Rollover	The maximum possible meter reading before the dials roll over to zero. The number of nines shown in this field corresponds to the number of meter dials. This setting is used with PCOMP, count rate, and counts to calculate the consumption value.
Scheme	Specifies whether to use a linear or exponential backoff scheme when scanning for a network.
Secondary DNS Server	No Cell Connection.
Security State	Ready to secure (enhanced security not enabled). The ERT or meter does not require secure commands or keys to execute any action on the device. Command Security. The ERT or meter responds to only secure commands. This includes open session commands and commands for connecting and disconnecting a customer's service. Full Security. The ERT or meter requires the use of secure commands and/or keys for all actions on the action command menu.
Service Control State	The latest requested state of the meter's shutoff valve. Connected. The shutoff valve will be opened and service will be connected. Disconnected. The shutoff valve will be closed and service will be disconnected. Ready for Reconnection. The shutoff valve will be armed for opening. An FSR must be on site to ensure conditions are safe for turning on the flow of gas, and to manually connect service to the meter.
Signal Path Loss	The path loss of power density.
Signal To Noise Ratio	The level of signal compared to the level of background noise.
SSID	The Service Set Identifier (SSID). Indicates the current Radio Frequency Local Area Network (RFLAN) setting the ERT or meter is set to use to connect to a network.
Step	When the Scheme value is set to linear, this defines the interval increment, in seconds, between scans.
Tamper Detection Values	The values detected for each of the device's available tamper events. Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
Tampers and Events	The number of tamper events recorded by the meter. Important: For some ERT and meter types, this field's value is a link to open a list of the device's current tampers and events. For more information, see Tampers and Events. Important: For 100W ERTs and for OpenWay Riva 500W ERT Modules operating in Mobile Mode, the View Event Log command is embedded within the Check and Read command's workflow Result and Success fields. Select View Event Log to re-engage the radio's communication with the ERT, and get the ERT's event log. The event log is viewable on the mobile device. When you are done viewing the event log, click Close to go back to the Check or Read results.
Temperature Corrected Index	The consumption value, with temperature compensation applied.
Test Modeor Test Mode Info	Indicates if the meter is in test mode: Not In Test Mode Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed alphabetically within this table.
Test Mode Maximum Time (Hour/s)	The amount of time, in hours, that the meter remains in test mode before it automatically exists test mode.
Test Mode Pulse Weight	The selected pulse weight that is used during test mode.
Test Mode Pulse Width (ms)	The selected pulse width that is used during test mode.
Tilt Tamper(100G)	The number of tilt tampers detected (0-3).
Tilt Debounce	The amount of time required for the mechanical contact on the tilt switch to settle before a signal from the switch is considered valid by the device. This setting is used to adjust the sensitivity of the meter removal tamper indicator. Tilt debounce values correspond to milliseconds (ms) as follows: 0. No tilt 1. 100 ms 2. 250 ms 3.500 ms
Time Drift	The hours, minutes, and seconds fast or slow the ERT module is, in relation to the actual time.
Tracking Area Code
Truncation	The number of least-significant (rightmost) digits (0-3) by which the module is programmed to truncate the meter reading. This value is required to prevent high-resolution readings recorded by nine-dial water registers from overflowing the ERT module's datalogging buckets. The overflow potential pertains primarily to commercial accounts that consume high volumes of water.
Type	The ERT model: for example, 100G.
Utility ID	The utility ID number assigned to your utility by Itron. This is a unique security code ranging from 0 to 32767 that prevents another utility from performing certain functions on an ERT module. If you enter a number greater than 32767, an error displays and you cannot save the utility ID.
Valve Actuation Count	The total number of times the module has opened or closed. This number includes operations performed as battery overrides and temperature override commands.
Valve Override	Indicates if the valve's current open or closed state is resulted from use of the valve override command. Not In an Override State.The valve state is not in its current open or closed state due to the meter's override feature.
Valve State	The meter valve's open or closed state: Open or sometimes Valve Open. The valve is open and gas is flowing. Closed or sometimes Valve Closed. The valve is closed and gas flow is stopped. Armed. The valve is primed to open when the meter's hardware button is pressed. Restrict. The valve is partially opened and water is flowing between 10-90% of the water's regular flow. Connected. The valve is open and water is flowing. Disconnected. The valve is closed and water flow is stopped. Important: For some meter types, this field's value is a link to open additional info. The additional info values are listed in this table.
Volume Under Alarm	The volume of usage that occurred under an alarm.